Dascom T2250 Quick Start Guide Instrukcja Użytkownika

Quick Start Guide T2150 T2250 Matrix Printer

➤ Connecting the printerMake sure that the printer and the computer are switched offand connect the data cable between the printer and the computer.Co

Control panel The control panel and the keys are used for controlling printer operation.The upper line of the display shows whether the printer is in

➤ Setup mode In this mode, the following settings are available: Setup key: Sets the printer to setup mode, in which the followingsettings can be sel

Changing theribbon cassetteRemove all the paper from the printer and make sure that the printer is switched off beforeopening the cover.Press the two

Turn the coloured ribbon feed knob at the right of the new ribboncassette in the direction of the arrow in order to take up slack ofthe ribbon.Slightl

Paper handling This section describes how to set the paper type, load fanfold paper and single sheets, transportpaper and move the paper to the tear p

➤ Loading paper Your printer can print both fanfold paper and single sheets. For information on the paper sizesyou can use, please refer to page 24 (P

Align the right-hand tractor to the width of the paper and insertthe paper. Make sure that it is inserted by the same length as onthe left-hand tracto

Single sheetsMake sure that the printer is set to single sheet mode. If necess-ary, change the paper type (see page 13, Paper path quickselection).Pre

➤ Paper transport Loaded paper can be transported in the printer in several ways.Make sure that the printer is in offline mode; press the Online key,

This device fulfils the European standards requirements by complying with the Directive of the Commission dated May 3, 1989 (89/336/EEC) relating to e

➤ Moving the paper tothe tear positionYou can use the Tea r key to move the paper to the tear position.Make sure that the printer is in online mode. P

Settings This section describes how to set the tear position, the first printing line, the print head gap aswell as the font and the character density

➤ Setting the firstprinting line (TOF)You can use the TOF function for setting the position of the first printing line for each papersource and each m

➤ Setting the print headgapThe printer features automatic print head gap adjustment to the thickness of the paper used (AGAfuncion). In setup mode, y

➤ Selecting characterdensity and fontYou can use the CPI key in setup mode to select the number of characters per inch to be printed.You can use the F

Quick Start-up Printing out status page23ENGLISHPrinting out status pageThe status page contains all selected menu settings and the installed control

Quick Start-up Specifications24ENGLISHSpecifications➤ Printer specificationsFor more information on printer specifications as well as interface specif

➤ Paper specificationsFor more information on general paper specifications as well as paper specifications for theoptional tractor units and the autom

“All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form re-quires our expli

Operator’s ManualQUICK START-UPTable of contentsQuick Start-up Table of contents1 Table of contents Introduction 2 Symbols used 2 Important safe

© October 2010 DASCOM Europe GmbH 063200cDASCOM REPRESENTATIVESGERMANYDASCOM Europe GmbHHeuweg 3D-89079 UlmDeutschlandTel.: +49 (0) 731 2075 0Fax: +49

Introduction This Operator’s Manual is intended as a quick introduction into working with the printer and isto enable also unexperienced users to hand

➤ Using theOnline-CD-ROMFirst install the Adobe Acrobat Reader on your hard disk unless the program has already beeninstalled. To install it, follow t

Printer at a glance pull to openpull to openControl panelFront coverPower switchPaper supportBottom coverManual single sheet feeder closedPower inlet

Installation➤ Unpacking the printer Place your printer on a solid base.Make sure that the “Up” symbols point to the correct direction.Open the packagi

➤ Placing your printer Place the printer on a solid, flat and non-slip surface in such a way that it cannot fall down. Makesure to facilitate access t

➤ Checking the printervoltageMake sure that the device has been set to the correct voltage (e.g. 230 V in Europe, 120 V in theUSA). To do this, check